Dodge 2010 Ram Manuel d'utilisateur

Ram TruckOWNE R ’ S MAN UAL2 0 1 0

THINGS TO KNOW BEFORE STARTING YOUR VEHICLECONTENTS䡵 A Word About Your Keys ... 12▫ Wireless Ignition Node (WIN) —If Equipped ...

until the head restraint reaches the first lock position,push the large button in and push down and adjust headrestraint to desired position.NOTE: Ens

Eight-Way Power Seats — If EquippedThe power seat controls are on the outboard side of thefront seat cushions. The power seat switch can be movedforwa

WARNING!Adjusting a seat while the vehicle is moving isdangerous. The sudden movement of the seat couldcause you to lose control. The seat belt might

WARNING!Adjusting a seat while the vehicle is moving isdangerous. The sudden movement of the seat couldcause you to lose control. The seat belt might

NOTE: The drivers heated seat can be programmed tocome on during a remote start. Refer to “Remote StartingSystem — If Equipped” in “Things to Know Bef

Ventilated Seats — If EquippedLocated in the seat cushion and seatback are small fansthat draw the air from around the occupant and exhaustit undernea

Mega Cab姞 Rear Seat FeaturesReclining Rear Seats — If EquippedThe recliner handle is located on the outside of the seatcushion. Pull upward on the han

Folding Rear Seat (Table Mode) — If EquippedBoth the left and right rear seatbacks can be folded downand used as a table.To fold down either rear seat

WARNING!•It is extremely dangerous to ride in a cargo area,inside or outside of a vehicle. In a collision, peopleriding in these areas are more likely

2. Fold the seatback down and push the seat forward. 3. Lift the seatback, to return the seat to the uprightposition. Be sure the seat is locked in pl

▫ Remote Open Window Feature —If Equipped ... 23▫ Using The Panic Alarm ... 24▫ Programming Additional Transmitter

The memory buttons 1 and 2 can be programmed torecall the driver’s seat position, driver’s outside mirrorposition, adjustable brake, accelerator pedal

2. Adjust the driver’s seat, recliner, and both sideviewmirrors to the desired positions.NOTE: Not all motors may be moved at one time. Referto “Seats

•Not all motors may be moved at one time. Refer to the“Seats/Eight-Way Power Seat” in this section for fur-ther information.To recall the memory setti

NOTE: The capability to link RKE transmitters tomemory is enabled when delivered from the factory. Thecapability to link RKE transmitters to memory ca

NOTE: The Easy Entry/Easy Exit feature can be en-abled or disabled through the programmable features inthe Electronic Vehicle Information Center (EVIC

2. Reach into the opening beneath the center of the hoodand push the safety latch lever from right to left to releaseit, before raising the hood.CAUTI

LIGHTSThe headlight switch is located on the left side of theinstrument panel, next to the steering wheel. The head-light switch controls the operatio

HeadlightsTo turn on the headlights, rotate the headlightswitch clockwise. When the headlight switch ison the parking lights, taillights, license plat

NOTE: The engine must be running before the head-lights will turn on in the Automatic Mode.SmartBeam™ — If EquippedThe SmartBeam™ system provides incr

Headlight DelayTo aid in your exit, your vehicle is equipped with aheadlight delay that will leave the headlights on forapproximately 90 seconds. This

▫ Driver And Right Front PassengerSupplemental Restraint System (SRS) –Airbag ... 50▫ Airbag System Components ...

The fog lights will operate only when the parking lightsare on or when the vehicle headlights are on low beam.An indicator light located in the instru

Cargo LightThe cargo lights are turned on by pressing on the cargobutton.The cargo lights will also turn on for approximately30 seconds when a RKE tra

Daytime Running Lights (DRL) (Canada Only andFleet Vehicles)The headlights on your vehicle will illuminate when theengine is started and the transmiss

NOTE: If either light remains on and does not flash, orthere is a very fast flash rate, check for a defective outsidelight bulb. If an indicator fails

WINDSHIELD WIPERS AND WASHERSWindshield WipersThe wipers and washers are operated by a switch in themultifunction lever. Turn the end of the handle to

Windshield WashersTo use the windshield washer, push the washer knob,located on the end of the multifunction lever, inward tothe second detent. Washer

Pull the lever toward the steering wheel to unlock thesteering column. With one hand firmly on the steeringwheel, move the steering column up or down,

The heated steering wheel switch is located on the switchbank below the climate controls.Press the switch to turn on the heatedsteering wheel. The lig

DRIVER ADJUSTABLE PEDALS — IF EQUIPPEDThe power adjustable accelerator and brake pedals allowthe driver to establish a comfortable position relative t

CAUTION!Do not place any article under the adjustable pedalsor impede its ability to move as it may cause damageto the pedal controls. Pedal travel ma

A WORD ABOUT YOUR KEYSKey Fob with Remote Keyless Entry (RKE) — IfEquippedYour vehicle uses a keyless ignition system. This systemconsists of a Key Fo

NOTE: In order to ensure proper operation, the Elec-tronic Speed Control System has been designed to shutdown if multiple Speed Control functions are

Deactivating Electronic Speed ControlA soft tap on the brake pedal or pulling the ElectronicSpeed Control lever (CANCEL) toward you will deacti-vate t

To Accelerate for PassingPress the accelerator as you would normally. When thepedal is released, the vehicle will return to the set speed.NOTE: The El

PARKSENSE姞 REAR PARK ASSIST — IFEQUIPPEDThe ParkSense威 Rear Park Assist system provides visualand audible indications of the distance between the rear

The ParkSense威 Warning Display is located in the instru-ment cluster’s EVIC display. It provides both visual andaudible warnings to indicate the dista

ParkSense威 will indicate a detected obstacle by showingthree solid arcs and will produce a1⁄2second tone. As thevehicle moves closer to the object the

The vehicle is close to the obstacle when the EVIC displayshows one flashing arc and sounds a continuous tone.Fast Tone Continuous Tone3UNDERSTANDING

WARNING DISPLAY DISTANCESDISPLAY MESSAGE OBSTACLE DISTANCE FROM: ARC’s AUDIBLE SIG-NALREAR CORNERS REAR CENTERPark Assist ON None NoneWarning Object D

Enable/Disable ParkSense姞ParkSense威 can be enabled and disabled with a switchlocated in the switch bank of the instrument panel orthrough the Customer

and the system is disabled, the EVIC will display the“PARK ASSIST DISABLED” message for as long as thevehicle is in REVERSE.The switch LED will be ON

Key FobThe Key Fob operates the ignition switch. It also containsthe Remote Keyless Entry (RKE) transmitter and anemergency key, which stores in the r

•When you turn ParkSense威 off, the instrument clusterwill display “PARK ASSIST DISABLED.” Further-more, once you turn ParkSense威 off, it remains offun

CAUTION!•The ParkSense威 Rear Park Assist system is only aparking aid and it is unable to recognize everyobstacle, including small obstacles. Parking c

WARNING! (Continued)•Before using the ParkSense威 Rear Park Assistsystem, it is strongly recommended that the ballmount and hitch ball assembly is disc

CAUTION!•To avoid vehicle damage, ParkView威 should onlybe used as a parking aid. The ParkView威 camera isunable to view every obstacle or object in you

Turning ParkView姞 On or Off — WithoutNavigation/Multimedia Radio1. Press the “menu” hard key.2. Select “system setup” soft key.3. Enable or disable th

Courtesy/Reading LightsBoth lights in the overhead console and rear passengercompartment will illuminate as courtesy lights when adoor is opened, when

NOTE: The courtesy/reading lights will remain on untilthe switch is pressed a second time, so be sure they havebeen turned off before leaving the vehi

The HomeLink威 buttons are located in the overheadconsole, and contain one, two or three dots/lines desig-nating the different HomeLink威 channels.NOTE:

Programming HomeLink姞Before You BeginIf you have not trained any of the HomeLink威 buttons,erase all channels before you begin training.To do this, pre

NOTE: Some gate operators and garage door openersmay require you to replace Step 3 with procedures notedin the “Gate Operator/Canadian Programming” se

To remove the emergency key, slide the mechanical latchat the top of the Key Fob sideways with your thumb andthen pull the key out with your other han

6. Firmly press and release the LEARN or TRAININGbutton. The name and color of the button may vary bymanufacturer.NOTE: You have 30 seconds in which t

successfully accepted the frequency signal. The EVICdisplay will change from “CHANNEL # TRAINING” to“CHANNEL # TRAINED.”If you unplugged the device fo

Troubleshooting TipsIf you are having trouble programming HomeLink威, hereare some of the most common solutions:•Replace the battery in the original tr

POWER SUNROOF — IF EQUIPPEDThe power sunroof switch is located on the overheadconsole between the courtesy/reading lights.NOTE: The Power Accessory De

Open Sunroof — Express ModeMomentarily pressing the switch rearward will activatethe Express Open Feature, causing the sunroof to openautomatically. D

Sunshade OperationThe sunshade can be opened manually. However, thesunshade will open automatically as the sunroof opens.NOTE: The sunshade cannot be

NOTE:•To ensure proper operation a MOPAR威 knob andelement must be used.•Do not exceed the maximum power of 160 Watts (13Amps) at 12 Volts. If the 160

•Inside the upper lid of the center storage compartment— if equipped.•Rear of the center console storage compartment —Quad Cab威 or Crew Cab.The key sy

All accessories connected to the outlet(s) should beremoved or turned off when the vehicle is not in use toprotect the battery against discharge.WARNI

CIGAR LIGHTER AND ASH RECEIVER — IFEQUIPPEDA removable ash receiver and cigar lighter are available.For vehicles with a bench seat the cupholder tray

(EVIC)/Personal Settings (Customer-ProgrammableFeatures)” in “Understanding Your Instrument Panel”for further information.WARNING!Never leave children

For vehicles equipped with an optional floor shifter.POWER INVERTER — IF EQUIPPEDA 115 Volt (150 Watts Maximum) outlet is located on thecenter stack o

The power inverter is designed with built-in overloadprotection. If the power rating of 150 Watts is exceeded,the power inverter will automatically sh

NOTE:•When the power inverter switch is pressed, there willbe a delay of approximately one second before thepower inverter status indicator turns on.

Front Instrument Panel Cupholders — FloorMounted ShifterFor vehicles equipped with bucket seats and a floormounted shifter there are two cupholders lo

Rear Cupholder — Crew CabCrew Cab vehicles are equipped with rear cupholderslocated in the center armrest.STORAGEGlove Box StorageThe glove box is loc

To open the upper glove box push upward on the handlerelease. The glove box door will automatically open.To open the lower glove box, pull on the hand

Door StorageFront Door Storage — If EquippedStorage areas and bottle holders (drivers side only) arelocated in the door trim panels.Rear Door Storage

Center Storage Compartment — If EquippedThe center storage compartment is located between thedriver and passenger seats. The storage compartmentprovid

With the upper lid closed, pull on the lower handle toopen the lower storage bin.Upper Storage Compartment Lower Storage Bin3UNDERSTANDING THE FEATURE

Second Row In-Floor Storage Bin — If EquippedIn-floor storage bins are located in front of the secondrow seats and can be used for extra storage. The

The system uses Key Fob with factory-mated RemoteKeyless Entry (RKE) transmitter and Wireless IgnitionNode (WIN) to prevent unauthorized vehicle opera

Seatback StorageLocated in the back of both the driver and passengerfront seats are pockets that can be used for storage.Storage (Regular Cab)The stor

Storage and Seats (Crew Cab)The Crew Cab models provide additional storage underthe rear seats. Lift the seats to access the storage com-partment.To o

REAR WINDOW FEATURESRear Window DefrosterThe rear window defroster button is located on theclimate control panel. Press this button to turn onthe rear

CAUTION! (Continued)•Do not use scrapers, sharp instruments, or abra-sive window cleaners on the interior surface of thewindow.•Keep all objects a saf

FOLD FLAT LOAD FLOOR — IF EQUIPPEDQuad Cab威 models with a 60/40 rear seat may beequipped with a folding load floor.WARNING!Do not operate the vehicle

2. Grasp the knob on the load floor and lift the knob untilthe load floor unfolds into position.3. Reverse the procedure to store the load floor.Posit

4. Reverse the procedure to put the load floor back in thesecured down position before you operate the vehicle.RAMBOX姞 — IF EQUIPPEDThe RamBox威 system

RamBox姞 Integrated Box Side Storage BinsCargo storage bins are located on both sides of the pickupbox. The cargo storage bins provide watertight, lock

The interior of the RamBox威 will automatically illumi-nate when the lid is opened. In addition to the automaticillumination switch, there is a manual

CAUTION!Leaving the lid open for extended periods of timecould cause the vehicle battery to discharge. If the lidis required to stay open for extended

CAUTION!Always remove the Sentry Keys威 from the vehicleand lock all doors when leaving the vehicle unat-tended.At the time of purchase, the original o

RamBox姞 Safety WarningCarefully follow these warnings to help prevent personalinjury or damage to your vehicle:WARNING!•Always close the storage bin c

NOTE: In the event of an individual being locked insidethe storage bin, the storage bin cover can be opened frominside of the bin by pulling on the gl

2. With the side gates open, position the extender fullyforward in the bed against the front panel.3. Rotate the side gates closed allowing the outboa

4. Rotate the center handle horizontally to secure the sidegates in the closed position.5. Lock the center handle using the vehicle key to securethe p

2. With the side gates open, position the extender so theoutboard ends align with the intended slots in the sidesof the bed.3. Rotate the side gates c

4. Rotate the center handle horizontally to secure the sidegates in the closed position.5. Lock the center handle to secure the panel into placeand as

To install the bed extender into the extender positionperform the following:1. Lower the tailgate.2. Make sure the center handle is unlocked and rotat

4. Rotate the handles to the horizontal position to secureinto place.WARNING!To reduce the risk of potential injury or propertydamage:•Cargo must be s

Bed Rail Tie-Down SystemCAUTION!The maximum load per cleat should not exceed250 lbs (113 kg) and the angle of the load on each cleatshould not exceed

out on the cleat and slide it to the detent nearest thedesired location. Make sure the cleat is seated in thedetent and tighten the nut.To remove the

VEHICLE SECURITY ALARM — IF EQUIPPEDThe Vehicle Security Alarm monitors the vehicle doorsand ignition for unauthorized operation. When the Ve-hicle Se

SLIDE-IN CAMPERSCamper ApplicationsCertain truck models are not recommended for slide-incampers. To determine if your vehicle is excluded, pleaserefer

2. Remove the connector bracket from the sill by press-ing inward in the locking tab.3. Disconnect the chassis wiring harness, ensuring theconnector b

2. Unlatch the tailgate and remove the support cables byreleasing the lock tang from the pivot.3. Raise the right side of the tailgate until the right

UNDERSTANDING YOUR INSTRUMENT PANELCONTENTS䡵 Instrument Panel Features ... 197䡵 Switch Bank Button Description ... 198▫ Upper Swit

䡵 Media Center 730N/430 (RER/REN/RBZ) —AM/FM Stereo Radio And CD/DVD/HDD/NAV — If Equipped ... 238▫ Operating Instructions — Voice Co

▫ Using This Feature ... 266▫ Controlling The iPod威 Using RadioButtons ... 266▫ Play Mode ...

▫ Automatic Temperature Control (ATC) —If Equipped ... 283▫ Summer Operation ... 288▫ Winter Operation ...

INSTRUMENT PANEL FEATURES1 — Headlight Switch 7 — 115v Power Inverter Outlet 13 — Transfer Case Position Switch2 — Instrument Cluster 8 — Power Outlet

SWITCH BANK BUTTON DESCRIPTIONUpper Switch BankThe upper switch bank is located on the center of theinstrument panel.1. TOW/HAULRefer to “Starting And

TABLE OF CONTENTSSECTION PAGE1INTRODUCTION...32THINGS TO KNOW BEFORE STARTING YOUR VEHICLE...

The Vehicle Security Alarm will also disarm if the vehicleis started with a programmed Sentry Key威. If an unpro-grammed Sentry Key威 is used to start a

Lower Switch BankThe lower switch bank is located on the center of theinstrument panel.1. HEATED SEATSRefer to “Understanding The Features Of Your Veh

INSTRUMENT CLUSTER — BASE200 UNDERSTANDING YOUR INSTRUMENT PANEL

INSTRUMENT CLUSTER — PREMIUM4UNDERSTANDING YOUR INSTRUMENT PANEL 201

INSTRUMENT CLUSTER DESCRIPTIONS1. TachometerThe Tachometer indicates engine speed in revolutions perminute.CAUTION!Do not operate the engine with the

CAUTION!Driving with a hot engine cooling system could damageyour vehicle. If temperature gauge reads “H” pull overand stop the vehicle. Idle the vehi

7. Electronic Throttle Control (ETC) LightThis light informs you of a problem with theElectronic Throttle Control (ETC) system. Thelight will come on

10. SERV (Service) 4WDThe SERV 4WD light monitors the electric shiftfour-wheel drive system. If the SERV 4WDlight stays on or comes on during driving,

NOTE: If the gauge pointer moves to either extreme ofthe gauge, the Check Gauges indicator will illuminateand a single chime will sound.15. Odometer/T

Vehicle Odometer MessagesWhen the appropriate conditions exist, the followingmessages will display in the odometer:ECO ... Fuel Saver

If the vehicle diagnostic system determinesthat the fuel filler cap is loose, improperlyinstalled, or damaged, a loose gascap indicatorwill display in

REMOTE KEYLESS ENTRY (RKE) — IFEQUIPPEDThe RKE system allows you to lock or unlock the doorsand activate the Panic Alarm from distances up toapproxima

the oil change indicator system (after performing thescheduled maintenance), refer to the following proce-dure:1. Turn the ignition switch to the ON p

NOTE: In vehicles with 4.7L or 5.7L engines, the highestavailable transmission gear is displayed in the lowerright corner of the Electronic Vehicle In

22. Cargo LightThe cargo light will illuminate when the cargolight is activated by pressing the cargo lightbutton on the headlight switch.23. Brake Wa

WARNING!Driving a vehicle with the red brake light on isdangerous. Part of the brake system may have failed.It will take longer to stop the vehicle. Y

Center (EVIC). Refer to ”Electronic Vehicle InformationCenter (EVIC) — If Equipped” for further information.25. Tire Pressure Monitoring Telltale Ligh

When the malfunction indicator is illuminated, the sys-tem may not be able to detect or signal low tire pressureas intended. TPMS malfunctions may occ

26. Malfunction Indicator Light (MIL)The Malfunction Indicator Light (MIL) is part ofan onboard diagnostic (OBDII) system whichmonitors the emissions

WARNING!A malfunctioning catalytic converter, as referencedabove, can reach higher temperatures than in normaloperating conditions. This can cause a f

30. Transmission Temperature Warning LightThis light indicates that there is excessive trans-mission fluid temperature that might occurwith severe usa

remain on continuously. Refer to “Occupant Restraints”in “Things To Know Before Starting Your Vehicle” forfurther information.32. Charging System Ligh

Remote Key Unlock, Driver Door/All Doors FirstThis feature lets you program the system to unlock eitherthe driver’s door or all doors on the first pre

Center (EVIC). Refer to ”Electronic Vehicle InformationCenter (EVIC) — If Equipped” for further information.WARNING!If a warning light remains on the

This system conveniently allows the driver to select avariety of useful information by pressing the switchesmounted on the steering wheel. The EVIC co

Steering wheel EVIC control button asit appears on the right side of thesteering wheel.Press and release the SELECT button for accessto main menus, su

•Left Front Turn Signal Light Out•Left Rear Turn Signal Light Out•Right Front Turn Signal Light Out•Right Rear Turn Signal Light Out•Park Assist Disab

•Charging System LightThis light shows the status of the electrical charg-ing system. The light should come on when theignition switch is first turned

•Engine Temperature Warning LightThis light warns of an overheated engine condi-tion. As temperatures rise and the gauge ap-proaches H, this indicator

cycles and the vehicle has been driven several miles atspeeds greater than 30 mph (48 km/h), see an authorizeddealer as soon as possible.•Transmission

Oil Change DueYour vehicle is equipped with an engine oil changeindicator system. The Oil Change Due message willflash in the EVIC display for approxi

When the DTE value is less than 30 miles (48 km)estimated driving distance, the DTE display will changeto a text display of ⬙LOW FUEL.⬙ This display w

Trip FunctionsPress and release the ODOMETER/TRIP ODOMETERbutton until one of the following Trip Functions displaysin the EVIC:•Trip A•Trip B•Elapsed

Flash Lamps with Remote Key LockThis feature will cause the turn signal lights to flash whenthe doors are locked or unlocked with the RKE transmit-ter

System (Customer Information Features)Press and release the UP or DOWN button until “SYS-TEM” displays in the EVIC and press the SELECT button.Press t

blocked or reduced airflow to the underhood ambienttemperature sensor caused by the snowplow. In addi-tion, on vehicles equipped with Automatic Temper

5. Complete one or more 360–degree turns (in an areafree from large metal or metallic objects) until the “CAL”indicator turns off. The compass will no

3. Press the DOWN button until the “Compass Variance”message is displayed in the EVIC, then press the SELECTbutton. The last variance zone number disp

the feature showing the system has been activated or thecheck-mark is removed, showing the system has beendeactivated.Enable/Disable the Rear Park Ass

1st Press RKEWhen Driver Door 1st Press is selected, only the driver’sdoor will unlock on the first press of the RKE transmitterUNLOCK button. When Dr

is pressed. To make your selection, press and release theSELECT button until a check-mark appears next to thefeature showing the system has been activ

a check-mark appears next to the feature showing thesystem has been activated or the check-mark is removed,showing the system has been deactivated.Aut

Tilt Mirror In ReverseWhen this feature is selected and the shift lever is placedin reverse gear, the side mirrors tilt downward to allowthe driver to

Display Fuel Saver — If EquippedThe “Fuel Saver Mode” message is located in theCompass/Temperature display, this message can beturned on or off. To ma

Sound Horn with Remote Key LockThis feature will cause the horn to chirp when the doorsare locked with the RKE transmitter. This feature can beturned

Operating Instructions — Uconnect™ Phone — IfEquippedRefer to “Uconnect™ Phone” in the Uconnect™ UserManual located on the DVD for further details.Clo

Show Time if Radio is OffWhen selected, this feature will display the time of dayon the touch screen when the radio is turned off. Proceedas follows t

To Manually Set the Clock — RER/REN1. Turn on the radio.2. Touch the screen where the time is displayed.3. Touch the screen where “User Clock” is disp

Show Time if Radio is OffWhen selected, this feature will display the time of dayon the touch screen when the radio is turned off. Proceedas follows t

MEDIA CENTER 130 (RES) — AM/FM STEREORADIO WITH CD PLAYER (MP3 AUX JACK)NOTE: The radio sales code is located on the lower rightside of the radio face

SEEK ButtonsPress and release the SEEK buttons to search for the nextlistenable station in AM/FM mode. Press the right switchto seek up and the left s

Push the rotary TUNE/SCROLL control knob a secondtime and MID will display. Turn the TUNE/SCROLLcontrol knob to the right or left to increase or decre

SET 2 in both AM and FM. This allows a total of 12 AMand 12 FM stations to be stored into pushbutton memory.The stations stored in SET 2 memory can be

If you insert a disc with the ignition ON and the radioON, the unit will switch from radio to CD mode andbegin to play when you insert the disc. The d

the current selection. Pressing and holding the SEEKbutton will allow faster scrolling through the tracks inCD and MP3 modes.TIME ButtonPress this but

Using the Panic AlarmTo turn the Panic Alarm feature ON or OFF, press andhold the PANIC button on the RKE transmitter for atleast one second and relea

Supported Medium Formats (File Systems)The medium formats supported by the radio are ISO 9660Level 1 and Level 2 and includes the Joliet extension.Whe

Supported MP3 File FormatsThe radio will recognize only files with the *.MP3 exten-sion as MP3 files. Non-MP3 files named with the *.MP3extension may

Loading times for playback of MP3 files may be affectedby the following:•Media - CD-RW media may take longer to load thanCD-R media•Medium formats - M

MEDIA CENTER 130 (RES/RSC) — AM/FMSTEREO RADIO WITH CD PLAYER (MP3 AUXJACK) AND SIRIUS RADIONOTE: The radio sales code is located on the lower rightsi

to seek up and the left switch to seek down. The radiowill remain tuned to the new station until you makeanother selection. Holding either button will

3. After adjusting the hours, press the right side TUNE/SCROLL control knob to set the minutes. The minuteswill begin to blink.4. Adjust the minutes u

Setting the Tone, Balance, and FadePush the rotary TUNE/SCROLL control knob and BASSwill display. Turn the TUNE/SCROLL control knob tothe right or lef

Toggle the MUSIC TYPE button to select the followingformat types:Program Type16-Digit CharacterDisplayNo program typeor undefinedNoneAdult Hits Adlt H

By pressing the SEEK button when the Music Type iconis displayed, the radio will be tuned to the next frequencystation with the same selected Music Ty

You may add a second station to each pushbutton byrepeating the above procedure with this exception: Pressthe SET/RND button twice and SET 2 will show

1. With the RKE transmitter buttons facing down, use aflat blade to pry the two halves of the RKE transmitterapart. Make sure not to damage the seal d

If you insert a disc with the ignition ON and the radioON, the unit will switch from radio to CD mode andbegin to play when you insert the disc. The d

the current selection. Pressing and holding the SEEKbutton will allow faster scrolling through the tracks inCD and MP3 modes.TIME ButtonPress this but

Supported Medium Formats (File Systems)The medium formats supported by the radio are ISO 9660Level 1 and Level 2 and includes the Joliet extension.Whe

Supported MP3 File FormatsThe radio will recognize only files with the *.MP3 exten-sion as MP3 files. Non-MP3 files named with the *.MP3extension may

Loading times for playback of MP3 files may be affectedby the following:•Media - CD-RW media may take longer to load thanCD-R media•Medium formats - M

Operation Instructions - Auxiliary ModeThe auxiliary (AUX) jack is an audio input jack whichallows the user to plug in a portable device such as anMP3

This feature allows you to plug an iPod威 into thevehicle’s sound system through a 16–pin connector, usingthe provided interface cable.UCI supports Min

Using This FeatureBy using the provided connection cable to connect aniPod威 to the vehicle’s UCI 16–pin connector port:•The iPod威 audio can be played

•Jump backward in the current track by pressing andholding the << RW button. Holding the << RWbutton long enough will take you to the begi

•RND button (available on sales code RES radio only):Pressing this button toggles between Shuffle ON andShuffle OFF modes for the iPod威.IftheRND icon

How To Use Remote StartAll of the following conditions must be met before theengine will remote start:•Shift lever in PARK•Doors closed•Hood closed•HA

•Pressing a PRESET button will display the currentlist on the top line and the first item in that list onthe second line.•To Exit List mode without se

Uconnect™ Multimedia (SATELLITE RADIO) — IFEQUIPPED (REN/RER/RBZ/RES RADIOS ONLY)Satellite radio uses direct satellite-to-receiver broadcast-ing techn

Sirius ID number will display. The Sirius ID numberdisplay will time out in two minutes. Press any button onthe radio to exit this screen.ESN/SID Acce

Operating Instructions - Uconnect™ Multimedia(Satellite) ModeNOTE: The ignition switch must be in the ON or ACCposition to operate the radio.SEEK Butt

MUSIC TYPE ButtonPressing this button once will turn on the Music Typemode for five seconds. Pressing the MUSIC TYPE buttonor turning the TUNE/SCROLL

You may add a second channel to each pushbutton byrepeating the above procedure with this exception: Pressthe SET button twice and SET 2 will show in

The LCD screen is located in the overhead compartmentconsole.NOTE: Refer to the “Uconnect™ Multimedia” section ofUconnect™ User Manual located on the

REMOTE SOUND SYSTEM CONTROLS — IFEQUIPPEDThe remote sound system controls are located on the rearsurface of the steering wheel. Reach behind the wheel

The button located in the center of the left hand controlwill tune to the next pre-set station that you haveprogrammed in the radio pre-set pushbutton

NOTE: If you experience difficulty in playing a particu-lar disc, it may be damaged (i.e., scratched, reflectivecoating removed, a hair, moisture or d

•Remote Start Aborted - Hood Ajar•Remote Start Aborted - Fuel Low•Remote Start Aborted - System FaultThe EVIC message stays active until the ignition

dials and inner push knobs. These comfort controls canbe set to obtain desired interior conditions.Front Blower ControlThere are four blower speeds. U

NOTE: If your air conditioning performance seemslower than expected, check the front of the A/C con-denser (located in front of the radiator), for an

Mix ModeAir is directed through the floor, defrost and sidewindow demist outlets. This setting works best incold or snowy conditions that require extr

•Continuous use of the Recirculation mode may makethe inside air stuffy and window fogging may occur.Extended use of this mode is not recommended.•In

MAX A/CFor maximum cooling, when MAXA/C is selected the A/C is turned onautomatically and the air is recircu-lated.NOTE: A/C cannot be deselected when

•The system can be controlled manually, if desired.•SYNC feature links the temperature controls, the pas-senger side temperature becomes the same as t

Automatic Operation1. Position the MODE control knob to the Auto positionon the Automatic Temperature Control (ATC) Panel.2. Position the BLOWER contr

blower will engage immediately if the Defrost mode isselected, or by adjusting the blower control knob andsetting the fan to any fixed speed.Manual Op

NOTE: In many temperature positions, the BI-LEVELmode is designed to provide cooler air out of the paneloutlets and warmer air from the floor outlets.

Recirculation ControlWhen outside air contains smoke, odors, orhigh humidity, or if rapid cooling is desired,you may wish to recirculate interior air

To Exit Remote Start Mode and Drive the VehicleBefore the end of the 15-minute cycle, press and releasethe UNLOCK button on the RKE transmitter to unl

Vacation/StorageAny time you store your vehicle or keep it out of service(i.e., vacation) for two weeks or more, run the airconditioning system at idl

Operating Tips290 UNDERSTANDING YOUR INSTRUMENT PANEL

STARTING AND OPERATINGCONTENTS䡵 Starting Procedures ... 297▫ Normal Starting ... 297▫ Automatic Transmission ...

▫ Shifting Procedure – Manually ShiftedTransfer Case ... 317▫ Transfer Case Position Indicator Light ... 318▫ Electronically Sh

䡵 Driving Off-Road ... 355䡵 Winch Usage (Power Wagon Only) —If Equipped ... 356▫ Things To Know Before Using

䡵 Tires — General Information ... 404▫ Tire Pressure ... 404▫ Tire Inflation Pressures ... 405▫ Tire Pressu

▫ Gasoline/Oxygenate Blends ... 428▫ E-85 Usage In Non-Flex Fuel Vehicles ... 428▫ MMT In Gasoline ... 429▫ Materials Ad

▫ Towing Requirements ... 447▫ Towing Tips ... 455䡵 Snowplow ... 457▫ 1500 Models Only ...

STARTING PROCEDURESBefore starting your vehicle, adjust your seat, adjust bothinside and outside mirrors, and fasten your seat belt.The starter should

Tip Start FeatureDo not press the accelerator. Turn the ignition switchbriefly to the START position and release it. The startermotor will continue to

Front doors may be opened with the inside door handlewithout lifting the lock plunger.Doors locked before closing will remain locked whenclosed.The em

If the engine has been flooded, it may start to run, but nothave enough power to continue running when the keyfob is released. If this occurs, continu

WARNING!Remember to disconnect the cord before driving.Damage to the 110-115 Volt electrical cord could causeelectrocution.AUTOMATIC TRANSMISSIONCAUTI

Key Ignition Park InterlockThis vehicle is equipped with a Key Ignition Park Inter-lock which requires the shift lever to be placed in PARKprior to tu

5. Using the screwdriver, press and hold the override tabthrough the access port (ringed circle) on the bottom ofthe steering column.6. Move the shift

5. Move the shift lever into the NEUTRAL position.6. The vehicle may then be started in NEUTRAL.7. Reinstall the override cover.Four–Speed Automatic T

Never use PARK while the vehicle is in motion. Applythe parking brake when leaving the vehicle in this range.Always apply the parking brake first, the

2 (Second)This range is for moderate grades and to assist brakingon dry pavement or in mud and snow. Begins at a stop inlow gear with automatic upshif

Temperature Warning Light” may illuminate and thetransmission may downshift out of OVERDRIVE untilthe transmission cools down. After the transmission

Transmission Limp Home ModeTransmission function is monitored for abnormal condi-tions. If a condition is detected that could result intransmission da

Five–Speed Automatic Transmission – IfEquippedThe shift lever display located in the instrument panelcluster indicates the transmission gear range. Th

power locks will not operate. This prevents you fromaccidentally locking your Key Fob in the vehicle. Remov-ing the Key Fob or closing the door will a

On vehicles equipped with 4.7L or 5.7L engines, use ofERS (or TOW/HAUL mode) also enables an additionalunderdrive gear which is not normally used duri

WARNING!Do not downshift for additional engine braking on aslippery surface. The drive wheels could lose theirgrip and the vehicle could skid.Screen D

WARNING! (Continued)•Your vehicle could move and injure you and othersif it is not completely in PARK. Check by trying tomove the shift lever back and

•the engine coolant (antifreeze) has reached normaloperating temperature;•vehicle speed is above approximately 30 mph(48 km/h);•the TOW/HAUL switch ha

Shifts into Overdrive (fourth gear) are allowed duringsteady cruise (for improved fuel economy) and automaticclosed-throttle downshifts to third gear

torque converter clutch is not engaged, it may seem asif the transmission is not shifting into Overdrive whencold. This is normal. Pressing the TOW/HA

moving the shift lever to the desired positions. The 4Hand 4L positions are intended for loose, slippery roadsurfaces only. Driving in the 4H and 4L p

WARNING!You or others could be injured if you leave thevehicle unattended with the transfer case in theNEUTRAL position without first fully engaging t

Shifting Procedure – Manually Shifted TransferCase2H ⇔ 4HShifting between 2H and 4H can be made with thevehicle stopped or in motion. If the vehicle i

Transfer Case Position Indicator LightThe “Transfer Case Position Indicator Light” in theinstrument cluster is used to alert the driver that the front

8. If a chime is not heard, program mode was canceledbefore the feature could be disabled. If necessary, repeatthe above procedure.Auto Unlock Doors —

•Neutral (NEUTRAL)This electronically shifted transfer case is designed to bedriven in the two-wheel drive position (2WD) for normalstreet and highway

3. When the shift is complete, the indicator light for theselected position will stop flashing and remain ON.If One Or More Shift Conditions Are Not M

When operating your vehicle in 4WD LOW, the enginespeed is approximately three times that of the 2WD or4WD LOCK positions at a given road speed. Take

4WD LOCKFour-Wheel Drive Lock Range - This range locks the frontand rear driveshafts together forcing the front and rearwheels to rotate at the same s

When the shift is complete, the position indicator lightfor the selected position will stop flashing and remainON.2WD⇔ 4WD LOCKRotate the 4WD control

3. While still rolling, rotate the transfer case controlswitch to the desired position.4. After the desired position indicator light is ON (notflashin

This electronically shifted transfer case provides fivemode positions:•Two-wheel drive high range (2WD)•Four-wheel drive automatic range (4WD AUTO)•Fo

the front and rear driveshafts together forcing the frontand rear wheels to rotate at the same speed. This isaccomplished by rotating the 4WD Control

2. The newly selected position indicator light will con-tinue to flash.3. The transfer case will not shift.NOTE: Before retrying a selection, make cer

Proper operation of four-wheel drive vehicles dependson tires of equal size, type and circumference on eachwheel. Any difference in tire size can caus

7. Repeat the above steps to alternate the availability ofthis feature.8. If a chime is not heard, the program mode wascanceled before the feature cou

4WD LOWFour-Wheel Drive Low Range - This range provides lowspeed four-wheel drive. Locks the front and rear drive-shafts together forcing the front an

the vehicle in motion, the transfer case will engage/disengage faster if you momentarily release the accelera-tor pedal after turning the control swit

NOTE: If Steps 1 or 2 of either the Preferred or AlternateProcedure are not satisfied prior to attempting the shift orif they no longer are being met

The locking axles are controlled by the axle locker switch.The switch has three positions, AXLE UNLOCK, REARLOCK, and FRONT/REAR LOCK. Under normal dr

WARNING!Do not use the locked axle position for normaldriving. A locked front axle is intended for off-roaddriving only. Locking the front axle during

(ORV) trails or recreation areas. You should always treadlightly and only use established roads, trails or ORVrecreational areas. The National Forest

CAUTION!The door sill height is 25 inches. Water may intrudeinto the interior of the vehicle at greater depths.Simultaneous Brake And Throttle Operati

WARNING!Always wear your seat belt and firmly tie downcargo. Unsecured cargo can become projectiles in anoff-road situation.When To Use Low RangeWhen

CAUTION!On icy or slippery roads, do not downshift at highengine RPMs or vehicle speeds because engine brak-ing may cause skidding and loss of control

CAUTION!Reduced tire pressures may cause tire unseating andtotal loss of air pressure. To reduce the risk of tireunseating, while at a reduced tire pr

a door is engaged, that door can only be opened by usingthe outside door handle even if the inside door lock is inthe unlocked position.WARNING!Avoid

Crossing Large RocksWhen approaching large rocks, choose a path whichensures you drive over the largest with your tires. Thiswill lift your undercarri

accelerator to avoid spinning the log out from under yourtires. Then ease the vehicle off the log using your brakes.CAUTION!Do not attempt to cross a

the vehicle if something goes wrong? If everythinglooks good and you feel confident, then change trans-mission into a lower gear, shift the transfer c

ability to proceed then make sure you are in 4L (LowRange) with the transmission in first gear (manuallyselect first gear on automatic transmissions)

WARNING!If the engine stalls or you lose headway or cannotmake it to the top of a steep hill or grade, neverattempt to turn around. To do so may resul

CAUTION!Water ingestion into the axles, transmission, transfercase, engine or vehicle interior can occur if you drivetoo fast or through too deep of w

CAUTION!Muddy waters can reduce the cooling system effec-tiveness by depositing debris onto the radiator.•Crossing Ditches, Streams, Shallow Rivers Or

form to the ground contour. Different terrain, tires, andvehicles require different tire pressure. Hard surfaces likerock and heavier vehicles require

vehicle impingement on the surroundings, then using atow strap to the vehicle tow hooks would be fast andeasy. If the vehicle is severely hung up or i

CAUTION!Damage can occur when spinning your tires at anexcessive high speed. Do not spin your tires fasterthan an indicated 35 mph (56 km/h).•Using th

WINDOWSPower Windows – If EquippedThe control on the left front door panel has UP-DOWNswitches that give you fingertip control of all powerwindows. Th

WARNING!Never use tow straps with end hooks or link twostraps with a clevis pin. These heavy metal objectscould become projectiles if a strap breaks,

as you power the winch in. Be careful not to allowslack in the cable as you recover the vehicle. Do not tryto guide the cable into the drum. If it sta

packed material. Packed foreign material can cause awheel imbalance and cleaning the wheels will correctthe situation.WARNING!Abrasive material in any

Care should be taken to avoid sudden accelerations whenboth rear wheels are on a slippery surface. This couldcause both rear wheels to spin, and allow

Flowing/Rising WaterWARNING!Do not drive on or across a road or path where wateris flowing and/or rising (as in storm run-off). Flow-ing water can wea

CAUTION! (Continued)•Driving through standing water may cause dam-age to your vehicle’s drivetrain components. Al-ways inspect your vehicle’s fluids (

DRIVING OFF-ROADCare should be taken when attempting to climb steephills or driving diagonally across a hill or slope. If naturalobstacles force you t

WINCH USAGE (POWER WAGON ONLY) — IFEQUIPPEDThings To Know Before Using Your WinchGeneral Winch InformationYour vehicle is equipped with an electric ve

Low Voltage InterruptYour winch is equipped with a device that will interruptwinch function if the vehicle charging system voltagedrops to a low level

Understanding The Features Of Your WinchWinch Components358 STARTING AND OPERATING

WARNING!Never leave children alone in a vehicle. Leavingunattended children in a vehicle is dangerous for anumber of reasons. A child or others could

1. Motor: The winch motor is powered by the vehiclecharging system and features a thermal protection switchthat automatically stops motor function in

Winch AccessoriesThe following accessories are necessary to attach thewinch to anchors, change direction of pull, and for safewinching.Gloves:Wire rop

Clevis/D-Shackles: TheD-Shackle is a safe means ofconnecting the looped ends ofcables, straps and snatchblocks. The shackle’s pin isthreaded to allow

WARNING! (Continued)•Always keep hands and clothing clear of the wirerope, hook and fairlead opening during operationand when spooling.•Never wrap wir

General InformationPractice using your winch before you get stuck. Some keypoints to remember when using your winch are:1. Always take your time to as

CAUTION! (Continued)•Always keep remote control lead clear of thedrum, wire rope and rigging.•Inspect for cracks, pinches, frayed wires, or looseconne

3. Disengage the clutch to allow free spooling of thewinch drum, rotate the clutch lever on the winch todisengage. Freespooling conserves battery powe

5. Pull the wire to the anchor point. Pull out enough wirerope to reach your anchor point. Be sure to keep a certainamount of tension on the wire as i

CAUTION!Always be certain the anchor you select will with-stand the load.NOTE: How to choose an anchor point: A secureanchor is critical to winching o

NOTE: Always ensure the clutch is fully engaged ordisengaged.9. Connect the remote control to the winch control box,located behind the front bumper. B

rough road conditions may trigger the auto reversefunction unexpectedly during auto closure. If thishappens, pull the switch lightly to the first dete

11. Check your anchor. Make sure all connections aresecured and free of debris before continuing with thewinching procedure.12. Check wire rope. The w

13. In certain situations youmay decide to throw a heavyblanket or similar object overthe wire rope. A heavy blan-ket can absorb energy shouldthe wire

For additional assistance, the winched vehicle can beslowly driven while being pulled by the winch. Continuepulling until the vehicle is on stable gro

section of the rope and reposition it to the opposite endof the drum, which will free up space for continuedwinching.16. Secure vehicle. Once recovery

NOTE: How to spool under no load: Arrange theremote control lead so it cannot be caught in the winch.Arrange the wire rope so it will not kink or tang

Rigging TechniquesVarious winching situations will require application ofother winching techniques. These could range from toolittle distance to achie

will enable you to change your pulling direction whilestill allowing the wire rope to be at 90° to wind properlyonto the spooling drum.Increasing Pull

vehicle’s frame/tow hook and run the wire rope througha snatch block. Disengage the clutch and, using thesnatch block, pull out enough wire to reach y

CAUTION!Prolonged operation of the steering system at the endof the steering wheel travel will increase the steeringfluid temperature and it should be

surfaces. Refer to “Fluids, Lubricants, and GenuineParts” in “Maintaining Your Vehicle” for furtherinformation.PARKING BRAKEThe foot-operated parking

Wind BuffetingWind buffeting can be described as the perception ofpressure on the ears or a helicopter-type sound in theears. Your vehicle may exhibit

WARNING!•Always fully apply the parking brake when leav-ing your vehicle or it may roll and cause damage orinjury. Also be certain to leave the transm

3500 Dual Rear Wheel Models OnlyThe brake system power assist is provided by a hydro-boost unit which shares fluid with the power steeringsystem. You

The system’s pump motor runs during an ABS stop toprovide regulated hydraulic pressure. The pump motormakes a low humming noise during operation. This

WARNING! (Continued)•The ABS cannot prevent accidents, includingthose resulting from excessive speed in turns,following another vehicle too closely, o

WARNING!•ABS cannot prevent the natural laws of physicsfrom acting on the vehicle, nor can it increasebraking or steering efficiency beyond that af-fo

Brake Assist System (BAS)The BAS is designed to optimize the vehicle’s brakingcapability during emergency braking maneuvers. TheBAS detects an emergen

Hill Start Assist (HSA)The HSA system is designed to assist the driver inlaunching a vehicle on an incline. HSA will maintain thelevel of brake pressu

The system will only work if the intended direction of thevehicle and vehicle gear match. For example, if theintended direction is forward up a hill a

WARNING! (Continued)•HSA is not a parking brake. If you stop the vehicleon a hill without putting the transmission inPARK or using the parking brake,

EVIC Equipped VehiclesHSA is a Customer Programmable Feature on a EVICequipped vehicle. If you wish to turn off the HSA feature,refer to “Customer Pro

Please pay close attention to the information in thissection. It tells you how to use your restraint systemproperly, to keep you and your passengers a

•Oversteer - when the vehicle is turning more thanappropriate for the steering wheel position.•Understeer - when the vehicle is turning less thanappro

(2WD/4WD AUTO/4WD LOCK/4WD LOW/NEUTRAL) transfer case. If you have a four-wheel drivevehicle, and want to determine which transfer case is onyour vehi

requiring ESP to be switched to the “Partial Off” mode isovercome, turn ESP back on by momentarily pressing theESP OFF switch. This may be done while

off at low vehicle speeds so that it will not interfere withoff-road driving but ESP function returns to provide thestability feature at speeds above

this light remains on after several ignition cycles and thevehicle has been driven several miles/kilometers atspeeds greater than 30 mph (48 km/h), se

TSC is only active in the default “ESP On” mode. TSC canbe disabled by pressing the ESP OFF switch and entering“ESP Partial Off” mode. It is not activ

NOTE:•P (Passenger) - Metric tire sizing is based on U.S.design standards. P-Metric tires have the letter “P”molded into the sidewall preceding the si

Tire Sizing ChartEXAMPLE:Size Designation:P = Passenger car tire size based on U.S. design standardsⴖ...blank...ⴖ = Passenger car tire based on Euro

EXAMPLE:Service Description:95 = Load Index— A numerical code associated with the maximum load a tire can carryH = Speed Symbol— A symbol indicating t

Tire Identification Number (TIN)The TIN may be found on one or both sides of the tire,however, the date code may only be on one side. Tireswith white

INTRODUCTIONCONTENTS䡵 Introduction ... 4䡵 How To Use This Manual ... 4䡵 Warnings And Cautions ...

WARNING!•It is extremely dangerous to ride in a cargo area,inside or outside of a vehicle. In a collision, peopleriding in these areas are more likely

Tire Terminology and DefinitionsTerm DefinitionB-Pillar The vehicle B-Pillar is a structural member of the body locatedbetween the front and rear door

Tire Loading and Tire PressureTire Placard LocationNOTE: The proper cold tire inflation pressure is listedon the driver’s side B-Pillar.Tire and Loadi

NOTE: Under a maximum loaded vehicle condition,gross axle weight ratings (GAWRs) for the front and rearaxles must not be exceeded. For further informa

6. If your vehicle will be towing a trailer, load from yourtrailer will be transferred to your vehicle. Consult thismanual to determine how this reduc

5STARTING AND OPERATING 403

WARNING!Overloading of your tires is dangerous. Overloadingcan cause tire failure, affect vehicle handling, andincrease your stopping distance. Use ti

WARNING! (Continued)•Unequal tire pressures from one side of the ve-hicle to the other can cause the vehicle to drift tothe right or left.•Always driv

CAUTION!After inspecting or adjusting the tire pressure, al-ways reinstall the valve stem cap. This will preventmoisture and dirt from entering the va

Tire Pressures for High Speed OperationThe manufacturer advocates driving at safe speedswithin posted speed limits. Where speed limits or condi-tions

original equipped tire on the front or rear axle of yourvehicle, but it is not. Installation of this limited-use sparetire affects vehicle handling. S

Lap/Shoulder Belt Operating Instructions1. Enter the vehicle and close the door. Sit back andadjust the seat.2. The seat belt latch plate is above the

Tread Wear IndicatorsTread wear indicators are in the original equipment tiresto help you in determining when your tires should bereplaced.These indic

WARNING!Tires and the spare tire should be replaced after sixyears, regardless of the remaining tread. Failure tofollow this warning can result in sud

WARNING!•Do not use a tire, wheel size or rating other thanthat specified for your vehicle. Some combinationsof unapproved tires and wheels may change

TIRE CHAINSUse “Class S” chains, or other traction aids that meet SAEType “S” specifications.Use “Class U” chains on 2500/3500 model trucks, or othert

CAUTION! (Continued)•Observe the tire chain manufacturer’s instructionson method of installation, operating speed, andconditions for usage. Always use

CAUTION!Do not use tire chains on 4x4 model trucks equippedwith P265/70R17, LT275/70R17, P275/60R20, tires.There may not be adequate clearance for the

tires. Rotation will increase tread life, help to maintainmud, snow and wet traction levels and contribute to asmooth, quiet ride.Refer to “Maintenanc

Dual Rear WheelsThe tires used on dual wheel assemblies should bematched for wear to prevent overloading one tire in a set.To check if tires are even,

TIRE PRESSURE MONITOR SYSTEM (TPMS)The Tire Pressure Monitoring System (TPMS) will warnthe driver of a low tire pressure based on the vehiclerecommend

have been received. The vehicle may need to be drivenfor up to 20 minutes above 15 mph (25 km/h) to receivethis information.As an example, assume your

3. When the belt is long enough to fit, insert the latchplate into the buckle until you hear a “click.”WARNING!• A belt buckled into the wrong buckle

NOTE:•The TPMS is not intended to replace normal tire careand maintenance, nor to provide warning of a tirefailure or condition.•The TPMS should not b

Tire Pressure Monitoring Low Pressure WarningsThe Tire Pressure Monitoring Telltale Lamp willilluminate in the instrument cluster, and an au-dible chi

1. This spare tire does not have a tire pressure monitor-ing sensor. Therefore, the TPMS will not monitor the tirepressure in the spare tire.2. If you

Tire Pressure Monitor System (TPMS) Tire LightLoad Inflation Switch Description (2500 Models) –If EquippedWARNING!Never operate your vehicle with the

Tire Light Load Inflation Switch Operation – IfEquipped•This vehicle may have different recommended tirepressure values between the front and rear tir

•The tire light load inflation switch will allow the driverto change between the max load inflation pressure(cold) low pressure warning threshold and

Tire Pressure Information label. The Supplemental TirePressure Information label is located on the rear face ofthe driver door. Use an accurate tire g

the max load inflation pressure (cold) values to switchthe TPMS system to the max load inflation pressure(cold) low pressure warning threshold. If aft

FUEL REQUIREMENTS3.7L and 4.7L EngineAll engines (except 5.7L engines) are de-signed to meet all emissions regulationsand provide excellent fuel econo

Reformulated GasolineMany areas of the country require the use of cleanerburning gasoline referred to as “Reformulated Gasoline.”Reformulated gasoline

WARNING! (Continued)• A shoulder belt placed behind you will not protectyou from injury during a collision. You are morelikely to hit your head in a c

•OBD II “Malfunction Indicator Light” on•poor engine performance•poor cold start and cold drivability•increased risk for fuel system component corrosi

Fuel System CautionsCAUTION!Follow these guidelines to maintain your vehicle’sperformance:•The use of leaded gas is prohibited by Federal law.Using le

Carbon Monoxide WarningsWARNING!Carbon monoxide (CO) in exhaust gases is deadly.Follow the precautions below to prevent carbonmonoxide poisoning:•Do n

FLEXIBLE FUEL (4.7L ENGINE ONLY) — IFEQUIPPEDE85 General InformationThe information in this section is for Flexible Fuel Ve-hicles (FFV) only. These v

Ethanol Fuel (E85)E85 is a mixture of approximately 85% fuel ethanol and15% unleaded gasoline.WARNING!Ethanol vapors are extremely flammable and could

•you drive the vehicle immediately after refueling for atleast 5 miles (8 km)Observing these precautions will avoid possible hardstarting and/or signi

NOTE: Use of the engine block heater (if equipped) isbeneficial for E85 startability when the ambient tempera-ture is less than 32°F (0°C).Cruising Ra

ADDING FUELThe fuel filler cap (gas cap) is located behind the fuelfiller door, on the left side of the vehicle. Open the fueldoor and remove the fuel

WARNING!•Never have any smoking materials lit in or nearthe vehicle when the gas cap is removed or thetank filled.•Never add fuel to the vehicle when

VEHICLE LOADINGCertification LabelAs required by National Highway Traffic Safety Admin-istration regulations, your vehicle has a certification labelaf

WARNING!• A lap belt worn too high can increase the risk ofinternal injury in a collision. The belt forces won’t beat the strong hip and pelvic bones,

Rim SizeThis is the rim size that is appropriate for the tire sizelisted.Inflation PressureThis is the cold tire inflation pressure for your vehicle f

CAUTION!Do not load your vehicle any heavier than the GVWRor the maximum front and rear GAWR. If you do,parts on your vehicle can break, or it can cha

Gross Combination Weight Rating (GCWR)The GCWR is the total permissible weight of your vehicleand trailer when weighed in combination.NOTE: The GCWR r

hitches are the most popular on the market today andthey’re commonly used to tow small- and medium-sizedtrailers.Weight-Distributing HitchA weight-dis

EXAMPLE — Without Weight-Distributing Hitch(Incorrect)EXAMPLE — With Weight-Distributing Hitch (Correct)5STARTING AND OPERATING 443

Fifth-Wheel HitchThe fifth-wheel hitch is a special high platform with acoupling that mounts over the rear axle of the tow vehiclein the truck bed. It

Weight Ratings)” for the website address that containsthe necessary information for your specific drivetrain.Trailer Hitch Classification DefinitionsC

Never exceed the maximum tongue weight stamped onyour bumper or trailer hitch.Consider the following items when computing theweight on the rear axle o

Towing RequirementsTo promote proper break-in of your new vehicle drive-train components the following guidelines are recom-mended:CAUTION!•Do not tow

WARNING! (Continued)•Safety chains must always be used between yourvehicle and trailer. Always connect the chains tothe frame or hook retainers of the

belt tongue is pressed into the buckle. Allow the retractorto take up the surplus webbing, and the buckles willhang vertically from the cab back exit

•Check for signs of tire wear or visible tire damagebefore towing a trailer. Refer to “Tires – GeneralInformation” in “Starting and Operating” for the

WARNING!•Do not connect trailer brakes to your vehicle’shydraulic brake lines. It can overload your brakesystem and cause it to fail. You might not ha

This display may also be used to display diagnosticinformation, if needed.•SC — Short Circuit to Ground•Sb — Short to Battery•CF — Controller Fault –

GAIN setting can be increased to a maximum of 10 ordecreased to a minimum of 0 (no trailer braking).GAINThe GAIN setting is used to set the trailer br

EVIC Display MessagesThe trailer brake control interacts with the ElectronicVehicle Information Center (EVIC). Display messages,along with a single ch

The Trailer Tow Package will include a four and seven-pin wiring harness. Use a factory approved trailer har-ness and connector.NOTE: Do not cut or sp

WARNING!Any work done to the vehicle’s electrical system orwiring should be performed by a qualified automo-tive technician. If done improperly it may

NOTE: Using “TOW/HAUL” mode or a lower gearrange while operating the vehicle under heavy operatingconditions will improve performance and extend trans

−Air ConditioningTurn off temporarily.SNOWPLOW1500 Models OnlyNOTE: Do not use this model vehicle for snowplowapplications.WARNING!Snowplows and other

Dodge Body Builders Guide. See your authorized dealer,installer or snowplow manufacturer for this information.There are unique electrical systems that

Inserting Latch Plate In Use Position2THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45

2. The total GVWR or the Front GAWR or the RearGAWR should never be exceeded.3. Cargo capacity will be reduced by the addition ofoptions or passengers

Operating TipsUnder ideal snow plowing conditions, 20 mph (32 km/h)should be maximum operating speed. The operatorshould be familiar with the area and

•Do not shift the transmission unless the engine hasreturned to idle and wheels have stopped. Make apractice of stepping on the brake pedal before shi

Recreational Towing Procedure (Manual ShiftTransfer Case) – If EquippedUse the following procedure to prepare your vehicle forrecreational towing:WARN

9. Repeat steps 7 and 8 with the transmission in DRIVE.10. Turn OFF the engine and place the ignition switch inthe OFF position.11. Shift the transmis

WARNING!You or others could be injured if you leave thevehicle unattended with the transfer case in theNEUTRAL position without first fully engaging t

Recreational Towing Procedure (Electronic ShiftTransfer Case) – If EquippedUse the following procedure to prepare your vehicle forrecreational towing:

8. Start the engine.9. Shift the transmission into REVERSE.10. Release the brake pedal for five seconds and ensurethat there is no vehicle movement.11

CAUTION!Damage to the transmission may occur if the trans-mission is shifted into PARK with the transfer case inNEUTRAL and the engine running. With t

of the mode position indicator lights will flash con-tinuously until all requirements are met or until theNEUTRAL button is released.•The ignition swi

WARNING!•If the black latch and black buckle are not prop-erly connected when the seat belt is used by anoccupant, the seat belt will not be able to p

CAUTION!•Do not use a bumper-mounted clamp-on tow baron your vehicle. The bumper face bar will bedamaged.•Do not disconnect the rear driveshaft becaus

WHAT TO DO IN EMERGENCIESCONTENTS䡵 Hazard Warning Flasher ... 472䡵 Jacking And Tire Changing ... 472▫ Jack Location ...

HAZARD WARNING FLASHERThe Hazard Warning flasher switch is located on theupper switch bank just below the radio.Press the switch to turn on the Hazard

Jack LocationThe jack and jack tools are stored under the frontpassenger seat.RemovalTo access the jack and jack tools you must remove theplastic acce

Remove the jack and tools by removing the wing bolt andsliding the assembly from under the seat.Jack and Tools (1500 Series)Jack and Tools (2500/3500

WARNING!After using the jack and tools, always reinstall themin the original carrier and location. While drivingyou may experience abrupt stopping, ra

3. Fold the flap and roll the jack tool kit into a cylindricalpackage (in direction of arrows) and tie to the jack usingthe tie straps.Folding Flap an

4. Place the jack and tools in the storage position holdingthe jack by the jack turn-screw, slip the jack and toolsunder the seat so that the bottom s

Removing The Spare TireRemove the spare tire before attempting to jack up thetruck. Attach the wheel wrench to the jack extension tube.Insert the tube

you will prefer a higher position. When you release theanchorage, try to move it up or down to make sure thatit is locked in position.Center Lap Belts

It is recommended that you stow the flat or spare toavoid tangling the loose cable.NOTE: The winch mechanism is designed for use withthe jack extensio

4. Turn the ignition OFF.5. Turn on the Hazard Warning flasher.6. Block both the front and rear of thewheel diagonally opposite the jackingposition. F

WARNING! (Continued)•Do not let anyone sit in the vehicle when it is on ajack.•Do not get under the vehicle when it is on a jack.•Only use the jack in

•1500 Series TrucksWhen changing a front wheel, place the scissors jackunder the rear portion of the lower control arm as shownbelow.Operate the jack

For 4x2 and 4x4 trucks, when changing a rear wheel,assemble the jack drive tube to the jack and connect thedrive tube to the extension tube. Place the

•2500/3500 Series TrucksFor 2500/3500 4x2 series trucks, when changing a frontwheel, place the bottle jack under the frame rail behindthe wheel. Locat

For 4x2 and 4x4 trucks, when changing a rear wheel,assemble the jack drive tube to the jack and connect thedrive tube to the extension tube. Place the

CAUTION!Before raising the wheel off the ground, make surethat the jack will not damage surrounding truck partsand adjust the jack position as require

WARNING!A loose tire or jack thrown forward in a collision orhard stop could injure someone in the vehicle. Al-ways stow the jack parts and the extra

CAUTION!•Use a back-and-forth motion to remove the hub cap.Do not use a twisting motion when removing thehub cap, damage to the hub cap finish may occ

How To Use The Automatic Locking Mode1. Buckle the combination lap/shoulder belt.2. Grasp the shoulder portion and pull downward untilthe entire belt

8-Stud — Dual Rear WheelsDual wheels are flat-mounted and center-piloted. The lugnuts are a two-piece assembly. When the tires are beingrotated or rep

These dual rear wheels should be tightened as follows:1. Tighten the wheel nuts in the numbered sequence to asnug fit.2. Retighten the wheel nuts in t

WARNING!A loose tire thrown forward in a collision or hardstop could injure the occupants in the vehicle. Havethe deflated (flat) tire repaired or rep

NOTE: When using a portable battery booster packfollow the manufacturer’s operating instructions andprecautions.CAUTION!Do not use a portable battery

WARNING!•Take care to avoid the radiator cooling fan when-ever the hood is raised. It can start anytime theignition switch is on. You can be injured b

CAUTION!Failure to follow these procedures could result indamage to the charging system of the booster vehicleor the discharged vehicle.1. Connect the

8. Disconnect the opposite end of the positive (+) jumpercable from the positive (+) post of the booster battery.9. Disconnect the positive (+) end of

CAUTION!•When “rocking” a stuck vehicle by moving be-tween 1st and REVERSE, do not spin the wheelsfaster than 15 mph (24 km/h), or drivetrain damagema

WARNING!•Chains are not recommended for freeing a stuckvehicle. Chains may break, causing serious injuryor death.•Stand clear of vehicles when pulling

CAUTION!Failure to follow these towing methods could resultin damage to the transfer case. Such damage is notcovered by the New Vehicle Limited Warran

INTRODUCTIONCongratulations on selecting your new Chrysler GroupLLC vehicle. Be assured that it represents precisionworkmanship, distinctive styling,

Once the warning is triggered, the BeltAlert威 will con-tinue to chime and flash the Seat Belt Reminder Light for96 seconds or until the driver’s seat

MAINTAINING YOUR VEHICLECONTENTS䡵 Engine Compartment — 3.7L ... 502䡵 Engine Compartment — 4.7L ... 503䡵 Engine Compartment — 5.7L

▫ Windshield Wiper Blades ... 516▫ Adding Washer Fluid ... 516▫ Exhaust System ... 517▫ Cooling System ...

䡵 Fluid Capacities ... 552䡵 Fluids, Lubricants And Genuine Parts ... 554▫ Engine ... 554▫ Chassis ...

ENGINE COMPARTMENT — 3.7L1 — Air Cleaner Filter 7 — Washer Fluid Reservoir2 — Automatic Transmission Dipstick (If Equipped) 8 — Power Steering Fluid R

ENGINE COMPARTMENT — 4.7L1 — Air Cleaner Filter 7 — Washer Fluid Reservoir2 — Automatic Transmission Dipstick 8 — Power Steering Fluid Reservoir3 — En

ENGINE COMPARTMENT — 5.7L1 — Air Cleaner Filter 7 — Washer Fluid Reservoir2 — Automatic Transmission Dipstick 8 — Integrated Power Module3 — Engine Oi

ONBOARD DIAGNOSTIC SYSTEM (OBD II)Your vehicle is equipped with a sophisticated onboarddiagnostic system called OBDII. This system monitorsthe perform

will appear the next time the vehicle is started. Thismight indicate a damaged cap. If the problem is detectedtwice in a row, the system will turn on

4. Approximately 15 seconds later, one of two things willhappen:a. The MIL will flash for about 10 seconds and thenreturn to being fully illuminated u

your vehicle. Refer to these manuals before attemptingany procedure yourself.NOTE: Intentional tampering with emissions controlsystems may void your w

Pregnant women should wear the lap part of the beltacross the thighs and as snug against the hips as possible.Keep the belt low so that it does not co

CAUTION! (Continued)•Your vehicle has been built with improved fluidsthat protect the performance and durability ofyour vehicle and also allow extende

NOTE: Under no circumstances should oil changeintervals exceed 6,000 miles (10 000 km) or six months,whichever occurs first.Engine Oil SelectionFor be

Lubricants which do not have both the engine oil certi-fication mark and the correct SAE viscosity grade num-ber should not be used.NOTE: For 2500/350

Engine Air Cleaner FilterRefer to “Maintenance Schedule” for further information.WARNING!The air induction system (air cleaner, hoses, etc.) canprovid

WARNING! (Continued)•Battery gas is flammable and explosive. Keepflame or sparks away from the battery. Do not usea booster battery or any other boost

Air Conditioner MaintenanceFor best possible performance, your air conditionershould be checked and serviced by an authorized dealerat the start of ea

Refrigerant Recovery and RecyclingR-134a Air Conditioning Refrigerant is a hydrofluoro-carbon (HFC) that is endorsed by the EnvironmentalProtection Ag

Windshield Wiper BladesClean the rubber edges of the wiper blades and thewindshield periodically with a sponge or soft cloth and amild nonabrasive cle

WARNING!Commercially available windshield washer solventsare flammable. They could ignite and burn you. Caremust be exercised when filling or working

WARNING!Exhaust gases can injure or kill. They contain carbonmonoxide (CO) which is colorless and odorless.Breathing it can make you unconscious and c

NOTE: These airbags are certified to the new Federalregulations for Advanced Airbags.The Advanced Front Airbags have a multistage inflatordesign. This

NOTE: Intentional tampering with emissions controlsystems can result in civil penalties being assessedagainst you.WARNING!A hot exhaust system can sta

Cooling SystemWARNING!You or others can be badly burned by hot coolant orsteam from your radiator. If you see or hear steamcoming from under the hood,

Refer to “Maintenance Schedule” for further information.Selection Of CoolantUse only the manufacturer’s recommended engine cool-ant (antifreeze). Refe

Please review these recommendations for using HybridOrganic Additive Technology (HOAT) engine coolant(antifreeze).When adding engine coolant (antifree

WARNING!•The warning words “DO NOT OPEN HOT” on thecooling system pressure cap are a safety precaution.Never add engine coolant (antifreeze) when thee

When additional engine coolant (antifreeze) is needed tomaintain the proper level, it should be added to thecoolant bottle. Do not overfill.Points to

•Do not change the thermostat for Summer or Winteroperation. If replacement is ever necessary, installONLY the correct type thermostat. Other designs

WARNING!•Use only manufacturer’s recommended brakefluid. Refer to “Fluids, Lubricants, and GenuineParts” in “Maintaining Your Vehicle” for furtherinfo

WARNING! (Continued)•Do not allow petroleum based fluid to contami-nate the brake fluid. Brake seal components couldbe damaged, causing partial or com

Limited-Slip Differentials This vehicle requires that4 oz. (118 ml) MOPAR威 Limited Slip Additive or equiva-lent be added to the gear lubricant. Refer

•Front Passenger Airbag•Front and Side Impact Sensors — if equipped•Steering Wheel and Column•Instrument Panel•Knee Impact Bolster•Front Seat Belt Pre

CAUTION!•Do not use chemical flushes in your transmissionas the chemicals can damage your transmissioncomponents. Such damage is not covered by theNew

2. The vehicle must be on level ground.3. Fully apply the parking brake and press the brakepedal.4. Place the shift lever momentarily into each gear p

To prevent dirt and water from entering the transmissionafter checking or replenishing fluid, make certain that thedipstick cap is properly reseated.

hot or cold weather and other extreme conditions willhave an adverse affect on paint, metal trim, and under-body protection.The following maintenance

CAUTION!Do not use abrasive or strong cleaning materials suchas steel wool or scouring powder which will scratchmetal and painted surfaces.Special Car

heavy soil and/or excessive brake dust, use MOPAR威Wheel Cleaner or equivalent or select a nonabrasive,non-acidic cleaner. Do not use scouring pads, st

Your leather upholstery can be best preserved by regularcleaning with a damp soft cloth. Small particles of dirtcan act as an abrasive and damage the

cleaner. Use caution when cleaning the inside rear win-dow equipped with electric defrosters or the right rearquarter window equipped with the radio a

cover, otherwise the cavity number of each fuse isstamped on the inside cover that corresponds to thefollowing chart.Cavity CartridgeFuseMiniFuseDescr

Cavity CartridgeFuseMiniFuseDescriptionJ09 30 AmpPinkBat – Plg/ElectricBrakeJ10 40 AmpGreenBat – L/Bar/Off-RoadJ11 30 AmpPinkBat – Sway/Thatchum/RearD

WARNING! (Continued)•Do not put anything on or around the airbagcovers or attempt to open them manually. You maydamage the airbags and you could be in

Cavity CartridgeFuseMiniFuseDescriptionM25 10 AmpRedBat – J1962 Diag/MirrorsM26 10 AmpRedBat – Ign Sw, WIN,PASSM27 15 AmpBlueBat – CHMSL/BrakeSwM28 10

Cavity CartridgeFuseMiniFuseDescriptionM41 15 AmpBlueIOD-SDARS/VES2–3/DVD/HFM/UGDO/Vanity LampM42 10 AmpRedIOD-HVAC, U/HoodLampM43 10 AmpRedHorn #2M44

CAUTION!•When installing the totally integrated power mod-ule cover, it is important to ensure the cover isproperly positioned and fully latched. Fail

NOTE:•When reinstalling the IOD fuse push firmly until fullyseated; the gauges in the instrument cluster will do afull sweep when the ignition switch

BULB REPLACEMENTDual or Quad Headlamp/Front Park and TurnSignal — If Equipped1. Open the hood.2. Disconnect and isolate the negative battery cable.3.

8. Reach through the access hole of the wheel housesplash shield and lift the slide lock upward far enough todisengage it from the lock post on the ba

Fog Lamps1. Reach under and behind the front bumper to accessthe back of the front fog lamp housing.2. Disconnect the fog lamp wiring harness connecto

2. Pull the outboard side of the lamp rearward farenough to unsnap the two receptacles on the outboardside of the lamp housing from the two plastic sn

2. Separate the connector holding the housing and wir-ing harness to the body.3. Turn the desired bulb socket1⁄4turn and remove thesocket and bulb fro

4. Pull the desired bulb straight from the socket.CAUTION!Do not contaminate the bulb glass by touching itwith your fingers or by allowing it to conta

The system includes sensors adjacent to both front andrear seat occupants that are calibrated to deploy theSABIC airbags during impacts that require a

2. Rotate the socket1⁄4turn and pull it from the lampassembly.3. Pull the bulb straight from it’s socket and replace.7MAINTAINING YOUR VEHICLE 549

Rear Lamp Bar ID Marker (Dual Rear Wheels) — IfEquipped1. Loosen the two screws and the housing to gain accessto the bulb sockets.2. Turn the socket1⁄

Side Marker Lamps (Dual Rear Wheels) — IfEquipped1. Push rearward on the side marker lamp assembly.2. Pull the entire assembly from the fender.3. Turn

FLUID CAPACITIESU.S. MetricFuel (Approximate)1500 Regular Cab Shortbed/Crew Quad Cab Models 26 Gallons 98 Liters1500 Regular Cab Longbed/Crew Quad Cab

U.S. MetricCooling System3.7L Engine (MOPAR威 Antifreeze/Coolant 5Year/100,000 Mile Formula or equivalent)14 Quarts 13 Liters4.7L Engine (MOPAR威 Antifr

FLUIDS, LUBRICANTS AND GENUINE PARTSEngineComponent Fluid, Lubricant, or Genuine PartEngine Coolant MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Form

ChassisComponent Fluid, Lubricant, or Genuine PartAutomatic Transmission MOPAR威 ATF+4威 Automatic Transmission Fluid or equivalent licensedATF+4威 produ

MAINTENANCE SCHEDULESCONTENTS䡵 Emissions Control System Maintenance ... 558䡵 Maintenance Schedule ... 558▫ Required Maintenance Inte

EMISSIONS CONTROL SYSTEM MAINTENANCEThe Scheduled Maintenance services listed in bold typemust be done at the times or mileages specified to ensurethe

WARNING!Infants in rear-facing child restraints should NEVERride in the front seat of a vehicle with a passengerfront airbag. An airbag deployment can

NOTE:•The oil change indicator message will not monitor thetime since the last oil change. Change your vehicle’soil if it has been six months since yo

•Inspect the battery and clean and tighten the terminalsas required.•Check the fluid levels of the coolant reservoir, brakemaster cylinder, power stee

6,000 Miles (10,000 km) or6 Months Maintenance ServiceSchedule❏ Change the engine oil and engine oilfilter.❏ Rotate the tires.❏ Lube the front drive s

18,000 Miles (30,000 km) or18 Months MaintenanceService Schedule❏ Change the engine oil and engine oilfilter.❏ Rotate the tires.❏ Lube the front drive

30,000 Miles (50,000 km) or30 Months MaintenanceService Schedule❏ Change the engine oil and engine oilfilter.❏ Rotate the tires.❏ Replace the engine a

42,000 Miles (70,000 km) or42 Months MaintenanceService Schedule❏ Change the engine oil and engine oilfilter.❏ Rotate the tires.❏ Lube the front drive

54,000 Miles (90,000 km) or54 Months MaintenanceService Schedule❏ Change the engine oil and engine oilfilter.❏ Rotate the tires.❏ Lube the front drive

60,000 Miles (100,000 km) or 60 Months Maintenance Service Schedule❏ Change the engine oil and engine oil filter.❏ Rotate the tires.❏ Replace the engi

66,000 Miles (110,000 km) or66 Months MaintenanceService Schedule❏ Change the engine oil and engine oilfilter.❏ Rotate the tires.❏ Lube the front driv

78,000 Miles (130,000 km) or78 Months MaintenanceService Schedule❏ Change the engine oil and engine oilfilter.❏ Rotate the tires.❏ Lube the front driv

WARNING!•Relying on the airbags alone could lead to moresevere injuries in a collision. The airbags workwith your seat belt to restrain you properly.

90,000 Miles (150,000 km) or 90 Months Maintenance ServiceSchedule❏ Change the engine oil and engine oil filter.❏ Rotate the tires.❏ Replace the engin

96,000 Miles (160,000 km) or 96 Months Maintenance ServiceSchedule❏ Change the engine oil and engine oil filter.❏ Rotate the tires.❏ If using your veh

108,000 Miles (180,000 km) or 108 Months Maintenance ServiceSchedule❏ Change the engine oil and engine oil filter.❏ Rotate the tires.❏ If using your v

120,000 Miles (200,000 km) or 120 Months Maintenance Service Schedule❏ Change the engine oil and engine oil filter.❏ Rotate the tires.❏ Replace the en

126,000 Miles (210,000 km) or126 Months MaintenanceService Schedule❏ Change the engine oil and engine oilfilter.❏ Rotate the tires.❏ Lube the front dr

138,000 Miles (230,000 km) or138 Months MaintenanceService Schedule❏ Change the engine oil and engine oilfilter.❏ Rotate the tires.❏ Lube the front dr

† This maintenance is recommended by the manufacturerto the owner, but is not required to maintain emissionswarranty.WARNING!•You can be badly injured

IF YOU NEED CONSUMER ASSISTANCECONTENTS䡵 Suggestions For Obtaining Service For YourVehicle ... 579▫ Prepare For The Appoint

䡵 Publication Order Forms ... 583䡵 Department Of Transportation Uniform TireQuality Grades ... 584▫ Treadwear ...

The Advanced Front Airbags will not deploy in all frontalcollisions, including some that may produce substantialvehicle damage — for example, some pol

SUGGESTIONS FOR OBTAINING SERVICE FORYOUR VEHICLEPrepare For The AppointmentIf you’re having warranty work done, be sure to have theright papers with

This is why you should always talk to an authorizeddealer’s service manager first. Most matters can be re-solved with this process.•If for some reason

Customer Assistance For The Hearing Or SpeechImpaired (TDD/TTY)To assist customers who have hearing difficulties, themanufacturer has installed specia

has also made a major investment in facilities, tools, andtraining to assure that you are absolutely delighted withthe ownership experience. You’ll be

If NHTSA receives similar complaints, it may open aninvestigation, and if it finds that a safety defect exists ina group of vehicles, it may order a r

vehicle, system, and/or components is written instraightforward language with illustrations, diagrams,and charts.•Diagnostic Procedure ManualsDiagnost

in each category is shown on the sidewall of the tires onyour vehicle.All passenger car tires must conform to Federal safetyrequirements in addition t

grade C corresponds to a level of performance, which allpassenger car tires must meet under the Federal MotorVehicle Safety Standard No. 109. Grades B

INDEX10

Adding Fuel ...436Adjustable Pedals ...127Air Cleaner, Engine (Engine Air Cleaner Filter) . . . 512Air Con

It also includes diagnostics that will illuminate the instru-ment cluster Airbag Warning Light if a malfunction isnoted. The diagnostics also record t

Fluid Type ... 528,555Gear Ranges ...303Shifting ...308Special Additives ...

Radiator (Coolant Pressure) ...522Car Washes ...532Carbon Monoxide Warning ... 78,431Cargo Light ...

Coolant Level ...520,523Disposal of Used Coolant ... 523Drain, Flush, and Refill ... 520Inspection ...

Electronic Brake Control System ...382Anti-Lock Brake System ...382Brake Assist System ...384Electronic Stabi

Exterior Lighting ... 116Exterior Lights ...79FiltersAir Cleaner ... 512Engine Oil

Octane Rating ... 427,554Requirements ...427,552Saver Mode ...227,228Tank Capacity ...

Automatic ...116Cleaning ... 535High Beam ... 122High Beam/Low Beam Select Swi

Jack Location ... 472Jump Starting ... 491Key, Programming ...17Key, Replacement .

Four-Wheel Drive Indicator ...318Hazard Warning Flasher ...472Headlights ... 116High Beam ...

Maintenance Schedule ... 558Malfunction Indicator Light (Check Engine) ...506Manual, Service ... 583Manual Tr

1INTRODUCTION 5

deploy the SABIC airbags, depending on severity andtype of collision. In these events, the ORC will deploy theSABIC only on the impact side of the veh

Dipstick ... 509Disposal ... 511Filter ... 511,554Filter Disposal ...

Sliding Rear Window ... 172Steering ...376,377Sunroof ... 152Windows ...

Reporting Safety Defects ...582Resetting Oil Change Indicator ...208,226Restraint, Head ...97Restraints

Selection of Coolant (Antifreeze) ...521,554Sentry Key (Immobilizer) ... 15Sentry Key Programming ... 17Sentry

Steering Wheel Mounted Sound SystemControls ... 276Storage Compartment, Center Seat ...166Storage, Vehicle ...

Safety ...394,404Sizes ...396Snow Tires ...414Spinning ...

Transmitter, Remote Keyless Entry (RKE) ... 20Tread Wear Indicators ...409Trip Odometer ...206Turn Signal

Usage ... 356Wind Buffeting ...37,154Window Fogging ...289Windows ...

Chrysler Group LLC10D241-126-AB2nd EditionPrinted in U.S.A.

•Turn on the interior lights, which remain on as long asthe battery has power or until the ignition key isremoved.•Unlock the doors automatically.If a

WARNING!Deployed airbags and seat belt pretensioners cannotprotect you in another collision. Have the airbags,seat belt pretensioners, and the front p

WARNING! (Continued)•Do not attempt to modify any part of your ad-vanced airbag system. The airbag may inflateaccidentally or may not function properl

located on the inside of the fuse block cover for theproper airbag fuses. See your authorized dealer if thefuse is good.Event Data Recorder (EDR)In th

accessing the electronic data stored, unless ordered todownload data by a court with legal jurisdiction (i.e.,pursuant to a warrant). A copy of the da

United States and all Canadian provinces require thatsmall children ride in proper restraint systems. This is thelaw, and you can be prosecuted for ig

infant carriers do, so they can be used rearward-facingby children who weigh more than 20 lbs (9 kg) but areless than one year old.•Rearward-facing ch

Here are some tips for getting the most out of your childrestraint:•Before buying any restraint system, make sure that ithas a label certifying that i

WARNING!Improper installation can lead to failure of an infantor child restraint. It could come loose in a collision.The child could be badly injured

WARNINGS AND CAUTIONSThis Owner’s Manual contains WARNINGS against op-erating procedures that could result in an accident orbodily injury. It also con

some time. In fact, many child restraint manufacturerswill provide add-on tether strap kits for some of theirolder products.Because the lower anchorag

Installing the Child Restraint SystemWARNING!Do not install child restraint systems equipped withLATCH attachments in the center position of a QuadCab

Installing Child Restraints Using the Vehicle SeatBeltThe seat belts in the passenger seating positions areequipped with either an Automatic Locking R

WARNING!An incorrectly anchored tether strap could lead to seatfailure and injury to the child. In a collision, the seatcould come loose and allow the

Multiple Child Restraint Installation Sequence(Quad Cab威/Crew Cab/Mega Cab威 - Rear Seats)Quad Cab威/Mega Cab威1. Obtain tether straps by raising the hea

4. Route each tether strap to the anchor behind the centerseat, and attach the hooks to the metal ring.5. Place a child restraint on the center rear s

Crew Cab1.The tether straps loops are located between the rear glassand the rear seat. There is a tether strap loop located behindeach seating positio

6. Install each child restraint and remove the slack in thetether strap according to the child restraint manufactur-er’s instructions.Children Too Lar

The engine oil installed in the engine at the factory is ahigh-quality energy conserving type lubricant. Oilchanges should be consistent with anticipa

Exhaust GasWARNING!Exhaust gases can injure or kill. They contain carbonmonoxide (CO), which is colorless and odorless.Breathing it can make you uncon

VEHICLE IDENTIFICATION NUMBERThe Vehicle Identification Number (VIN) is found on theleft front corner of the instrument panel, visible throughthe wind

Safety Checks You Should Make Inside theVehicleSeat BeltsInspect the belt system periodically, checking for cuts,frays, and loose parts. Damaged parts

Door LatchesCheck for positive closing, latching, and locking.Fluid LeaksCheck area under vehicle after overnight parking for fuel,engine coolant, oil

UNDERSTANDING THE FEATURES OF YOUR VEHICLECONTENTS䡵 Mirrors ... 87▫ Inside Day/Night Mirror ... 87▫ Automatic

▫ Adjustable Head Restraints ... 97▫ Eight-Way Power Seats — If Equipped ... 100▫ Power Lumbar — If Equipped ... 101▫ Heated Seat

▫ Daytime Running Lights (DRL)(Canada Only And Fleet Vehicles) ... 121▫ Multifunction Lever ... 121䡵 Windshield Wipers And Washer

䡵 Parkview威 Rear Back Up Camera —If Equipped ... 141▫ Turning Parkview威 On Or Off —With Navigation/Multimedia Radio ... 142

䡵 Electrical Power Outlets ... 154䡵 Cigar Lighter And Ash Receiver —If Equipped ... 158䡵 Power Inverter — If Equi

䡵 Fold Flat Load Floor — If Equipped ... 173䡵 Rambox威 — If Equipped ... 175▫ Rambox威 Integrated Box SideStorage Bins ...

MIRRORSInside Day/Night MirrorHeadlight glare can be reduced by moving the smallcontrol lever under the mirror to the night position (leverflipped tow

Automatic Dimming Mirror — If EquippedThis mirror automatically adjusts for headlight glarefrom vehicles behind you. You can turn the feature on oroff

WARNING!Vehicles and other objects seen in a passenger sideconvex mirror will look smaller and farther awaythan they really are. Relying too much on y

Power Mirrors — If EquippedThe controls for the power mirrors are located on thedriver’s door trim panel.The power mirror controls consist of mirror s

To adjust a mirror, press the mirror select button for themirror that you want to adjust. Using the mirror controlswitch, press on any of the four arr

Illuminated Vanity Mirror — If EquippedIlluminated vanity mirrors are located on each sun visor.To use the mirror, rotate the sun visor down and swing

Trailer Towing Mirrors — If EquippedThese mirrors are designed with an adjustable mirrorhead to provide a greater vision range when towingextra-wide l

Uconnect™ Phone — IF EQUIPPEDRefer to “Uconnect™ Phone” in the Uconnect™ UserManual located on the DVD for further details.VOICE COMMAND — IF EQUIPPED

Manual Seat Adjuster — If EquippedBoth front seats are independently adjustable forward orrearward and are equipped with a seatback recliner. Themanua

WARNING!Adjusting a seat while the vehicle is moving isdangerous. The sudden movement of the seat couldcause you to lose control. The seat belt might

WARNING!•Actuating the recliner handle will allow the seat-back to swing (dump) forward on manual reclinerseats. Do not stand or lean in front of the

To raise the head restraint, pull upward on the headrestraint. To lower the head restraint, press the largebutton, located on the base of the head res